Comments on: Deck Mate Screws: The Best For Deck Construction?

By: MNhandy

MNhandy — Sun, 20 Sep 2009 14:39:58 +0000

We have owned several homes and I have built many decks, fences and other projects for our own use and for our friends and family. In late 2005 I used DeckMate screws (#8 x 2-1/2″) in 5/4″ ACQ decking for the first time. I loved them when I installed them. Now I need to replace popped screws every spring, and not just a few… LOTS. Heads are rusty, screws are breaking off every season in the threads below the shank, and I have never seen anything like this. These Phillips DeckMate screws are crap!! I am now reading about many other similar experiences, and I followed the instructions on their “Lifetime Guarantee” product to a tee. Today I have replaced hundreds, and am about to replace hundreds more. DON’T BUY DECKMATE SCREWS. At installation, they’re great. After a year or so of weathering, get ready for rusting, breakage, and popping.

By: theraphy

theraphy — Wed, 11 Mar 2009 09:51:16 +0000

I hope I can actually get a chance to try these.

By: Bruce

Bruce — Mon, 16 Feb 2009 19:03:58 +0000

#2 Robertson bits work even better in these screws than the proprietary bit.

#2 and #3 Phillips bits work about equally badly, and cam out at such low torque as to be virtually unusable. If you lose the Deck-Mate bit, go get some #2 Robertson bits and use those.

By: Ricardo Furioso

Ricardo Furioso — Mon, 22 Sep 2008 20:35:18 +0000

I was the attendee at the Maker Faire who recommended Toolmonger look into Deckmates. Having been disappointed and wanting an explanation of the swtich to Torx head screws, I called the number on the web site at deckmatescrews.com (1-888-332-6283 ) which is actually Phillips Fastener Products, a subsidiary of Phillips Screw Company. Spoke with an nice-but-overwhelmed-sounding woman there who said A) Home Cheapo owns the name Deckmate and has stopped buying screws from Phillips. B) So Home Cheapo is now putting the Deckmate name on junk screws. C) But Home Cheapo has figured out that the junk screws suck. D) And she said that Home Cheapo has come back to Phillips to ask them to once again furnish screws to be marketed at Home Cheapo. The questions she couldn’t answer are Will they be like the old Deckmates? (Probably) Will they have the blue driver tips? (Probably not.) When will they be back in Home Cheapo? (Christmas or so, 2008.) Meanwhile she said that Lowe’s carries several sizes of the blue-tip screws.

By: Drew

Drew — Wed, 18 Jun 2008 17:19:22 +0000

Just found out that the phillips/square drive screw that Home Depot used to cary is available at Lowes as Phillips II Driv screws. Sizes not in store are available at lowes.com.

By: Drew

Drew — Wed, 18 Jun 2008 17:02:31 +0000

I didn’t buy the star drive screws - but found some old stock of the square drive. Between the Deck Mate philips/square-driv bit and a #2 square drive
bit I can get these screws into (and out of) almost anything. Any hints on where to find/buy the “pre-star drive” stock? Has Deck Mate stopped making the old style?

By: Mark

Mark — Wed, 04 Jun 2008 03:06:02 +0000

Thank You Kevin!!! I feel the same way about those new torx drive Deck Mates. They SUCK!!! That’s how I found this site, by trying to find out if Deck Mate stopped making the Square Drive/Phillips screws, or if Home Cheapo just stopped carrying them. Maybe those Robertson ones are a good replacement.

By: Kevin

Kevin — Sat, 31 May 2008 01:29:44 +0000

They took away the good screws and put the new sucky deckmates in place. These new screws come with a hex-star drve that strip out quickly or you can’t insert the tip because the coating’s too thick.
Help Mr. Wizard!!

By: Reinhardt Quelle

Reinhardt Quelle — Tue, 19 Jun 2007 06:57:18 +0000

Sam says “Stainless screws are for suckers”… Er, I’m guessing he doesn’t work on the coast? Try this. Drive a DeckMate screw int o a board near the end. Use an old chisel to split the board open. Note how much of the coating rubbed off when the DeckMate went in. In my neck of the woods, that starts rusting within months, particularly when going into ACQ framing members.

Drive the DeckMate through tough, abrasive Ipe, and you’ll find even more of the coating is gone. “Lifetime warranty” notwithstanding, the things do rust.

Actually, the DeckMate is a great utility screw, and I buy ‘em by the 25lb box for other things, but not for decking, and I’ve never seen them with a trim head.

WRT the combo-drive vs. robertson vs. philips vs. Torx - every one of ‘em will strip if you tilt the driver, overdrive (go too fast), or use a worn bit. For me, the Torx is the only style really usable in stainless, which is quite soft, in ipe. And that’s with predrilling, which you have to do with Ipe.

I’m not a fan of deck clips or under-mounted fasteners. Its inevitable that you’re going to gouge, burn, or otherwise damage a board at some point in the future, and any system (like the Ipeclip) that makes it impossible to remove a single board from the middle of the deck is a no-go for me. Also, deck boards are a) not straight and b) not dry when you install them and any fastener that relies on a single screw strikes me as a great setup for callbacks.

By: Dan

Dan — Wed, 06 Jun 2007 14:32:17 +0000

If your building a deck I always use a hidden deck fastener like Ipe Clip which were designed so you dont screw into the face of your deck. Hidden deck fasteners are very good for hardwood decks and composite decks. I feel that if your going to invest money in a deck you might as well make it look good and reduce splitting, splintering, cupping and rotting at the same time. http://www.ipeclip.com

By: metis

metis — Mon, 04 Jun 2007 17:55:38 +0000

deckmate screws really are wonderful. they’re uniformly made for the price, are neigh on impossible to strip, and wet/outdoor rated. they’re not for layign drywall or hanging a picture, but for exposed/wet wood fastening i’ve yet to find anythign better. using “specialty” bits like torx or robertson leaves the client with a tamper resistant deck, but not one as easy to replace one board on.

torx and tamper torx i’ve not seen stripped, but the square, triangle, and allen heads can and do strip out.

By: Sam

Sam — Mon, 04 Jun 2007 00:45:21 +0000

I many hundreds of pounds of screws as a contractor and I can say that a.) the clutch on your drill does nothing to stop a screw from stripping, b.) stainless screws are for suckers, and c.) phillips-square head screws are the way to go. I use generic flavor, as they are cheaper than name brand and don’t have any stupid ridges or ribs or whatever to wear off the end of your bit.

By: Mr. Smartypants

Mr. Smartypants — Sun, 03 Jun 2007 19:37:11 +0000

Use the clutch on your drill/driver and eliminate any cam out problems with any srew design. Did some one forget to mention that Deckmates are guranteed forever? Also stainless screws can snap easier then regular steel. Deckmates are strong, last forever, hold tight, come in colors and are easy to buy at tons of places. What else do you want?

By: Pencilneck

Pencilneck — Sun, 03 Jun 2007 03:43:32 +0000

I built a wooden fence using Deck Mate screws around my back yard about 6 or 7 years ago. If I were to build another fence like it, I’d go with Deck Mate screws again. I ended up getting 3 boxes (don’t remember how many per box). Each box came with the bit. I wore out one bit, and went though most of the 3 box of screws with the second bit. The bits last a good while… longer than the number of screws in the box. Plus you can purchase extra bit if needed, they don’t cost that much.

The screws themselfs are pretty good quality, they don’t work loose. When I build a deck on my house in the next year, I’ll get some more boxes of Deck Mate screws since I know they work very well.

By: TL

TL — Fri, 01 Jun 2007 00:46:32 +0000

The Deck Mate screws and driver work better than a phillips, but not as good as a square drive with a GOOD bit. I suffer from the same mental inability to throw away a slightly worn square drive bit that previous posters have noted. It’s a sad disease which can screw up your project.

By: theminor

theminor — Tue, 29 May 2007 18:10:26 +0000

Square head for life.

By: Mike D in TO

Mike D in TO — Tue, 29 May 2007 15:33:45 +0000

Living in Canada - I use Robertson all the time as they don’t tend to strip or pop out unless your bit is worn as stated above. I think the biggest factor is what you are using to drive them in. I now use my impact driver instead of a drill as you have much more control and tend not to strip even the Phillips. Not to mention it doesn’t twist your arm and it will screw into the toughest materials with ease.

By: Abe

Abe — Sun, 27 May 2007 17:21:11 +0000

Why not just go torx and forget about it? I’ve never had a torx screw strip when driving into wood.

By: eschoendorff

eschoendorff — Sun, 27 May 2007 11:31:09 +0000

I want to echo what Bob said. These bits are a kind of Phillips-Robertson hybrid. That said, they do work. Very well, in fact.

If you are looking for a traditional phillips bit with anti-camout ribs, try these:

http://buy1.snapon.com/catalog/tools.asp?tool=all&Group_ID=717&store=snapon-store

They’re expensive, but they do a good job when used with manual screwdrivers.

By: James

James — Sat, 26 May 2007 23:32:57 +0000

I probably sound like a broken record, but McFeely’s sell good Robertson deck screws, like these #8 x 2-1/2″ Flat Head corrosion resistant screws:

http://www.mcfeelys.com/product/0824-FCT/Flat-Head-Steel-NoCoRode-PLUS

At $65 for 1000 and $130 for 2500, they’re pretty cheap, as well.

By: Blind

Blind — Sat, 26 May 2007 20:15:49 +0000

Has the patent on Posidriv expired yet? This just seems more and more like a solution to a non existent problem that has already been solved multiple times over.

By: Blind

Blind — Sat, 26 May 2007 20:06:01 +0000

Err, Robertson, not Robinson, my bad.

By: Blind

Blind — Sat, 26 May 2007 20:05:10 +0000

Like said above, Phillips head screws were designed for the driver to slip out to prevent the screw from being over torqued, so why would they design a head that behaves the exact opposite but still uses the same form factor?

Why not just use a Robinson or Hex or a make a larger Torx?

By: Frank Hicinbothem

Frank Hicinbothem — Sat, 26 May 2007 18:36:19 +0000

I’ll add my vote in favor of the Deck Mate screws. I use them pretty much everywhere. I get the best performance with the special bit, but as someone noted, they wear out quickly. But since a new one comes in every box, so what? And as someone else noted, you can always use a square drive or plain Phillips bit if you have to.

I like stainless steel square-drives for window installation, but I find it’s easy to get careless and use the square-drive bits beyond their limited lifetime. And frugal-me hates throwing them away because they’re “only a little worn.” Between window installs and pocket screws, I go through quite a few of them.

About the only thing I still use plain Phillips for is drywall, and that’s because my $%^& screw gun takes special screw strips that only come in plain Phillips.

By: Bob

Bob — Sat, 26 May 2007 17:58:42 +0000

Home Depot and Lowes both sell the DeckMate screws. I think the ones at Home Depot are a combo Phillips and square drive. So you can use one of three bits to drive it. Either a: phillips, square drive, or the combination phillips/square drive bit they sell with the screws. It looks like the picture in this post.

The ones sold at Lowes are just normal Phillips, but if you but their bit it has the anti-camout ridges on the bit that works with the ridges on the screw.

I could have the stores flip-flopped on who carries which type of screw.